Kissimmee, FL · Licensed AC contractor

AC Installation in Kissimmee, FL

New central air conditioners sized for Central Florida humidity, permitted with the city or county that covers your address, and installed by a licensed, insured local crew.

A replacement shouldn't copy the tonnage off the old unit's data plate. We start with a room-by-room load calculation and a look at the ducts, the electrical panel and the drain path. Then you get two or three options in writing. We file the permit with the City of Kissimmee, Osceola County or whichever office covers your parcel, and we stay with the job through final inspection.

AC installation services in Kissimmee FL

What we check at your assessment

Load calculationAn ACCA Manual J load calculation, with the equipment selected to match it.
DuctsIf the ducts need sealing or replacing, it's priced as its own line in your written options.
Electrical panelIf your home needs a new circuit or panel work, it's listed as a separate line too.
Drain pathA condensate drain with a secondary pan or float shut-off wherever an overflow could damage the house.
Licensed & insured
Load calculation before every quote
Permit filed for you

Your New AC at a Glance

An AC installation from us covers the whole system path, from the load calculation to the inspector's sign-off.

Included in every installation

  • ACCA Manual J load calculation, with equipment selected to match it
  • Removal of the old outdoor unit and indoor unit, with the refrigerant recovered as federal rules require
  • A new outdoor unit and indoor coil or air handler, rated by AHRI as a matched pair
  • Refrigerant lines flushed and reused or replaced, a level pad, and wind anchoring for the outdoor unit
  • Condensate drain, with a secondary pan or float shut-off wherever an overflow could damage the house
  • Electrical connection at the disconnect, and thermostat setup
  • Mechanical permit, startup testing, final inspection and a walkthrough

Priced as separate lines when the assessment calls for them:

  • Duct sealing or duct replacement
  • A new circuit or panel work
  • A raised or relocated pad
  • A surge protector at the outdoor unit
  • A Wi-Fi thermostat

How long it takes

Most straight changeouts take one working day on site. Duct or electrical work adds time; the timeline below shows how much.

AC Repair or Replacement: How to Decide

A system with years left should be fixed, not replaced. Florida systems log far more run hours each year than systems up north, so age alone doesn't settle it. These are the signs we weigh.

air conditioner installation in Kissimmee FL
Points toward repair
Points toward replacement
Tap the statements that describe your system.

Not sure which column you're in? Have our repair team diagnose it first. If the diagnosis points to a new system, everything below covers what happens next.

The Installation Journey: Assessment, Proposal, Install Day and Inspection

Here is the whole job, in the order it happens. Each stage that touches a Kissimmee permit office, utility or association says so.

Reaching us and booking the assessment

Reach out by phone at (844) 520-1341, and we'll set a time for the in-home visit. A few details up front make that visit more useful:

The in-home assessment

A technician measures rooms and windows, and notes which walls take the afternoon sun.

  • AtticMost Kissimmee homes sit on a slab, so the ducts and often the air handler are up here, in the hottest space in the house. We check insulation depth, duct condition, and the platform and access around the air handler.
  • PanelBreaker size, wire gauge, the disconnect, and room for a surge protector.
  • OutsideWhere the condenser sits, how it's anchored, and whether the pad is high enough for the lot. That last check matters in low areas along Shingle Creek, where Hurricane Ian flooded neighborhoods in 2022.

The load calculation comes next, before any equipment is chosen.

The written proposal

You get two or three options. Each one lists:
  • Outdoor and indoor model numbers, with the AHRI reference showing they're a rated match
  • SEER2 rating and compressor type (single-stage, two-stage or variable-speed)
  • The refrigerant the system uses
  • What's included, and which add-ons are priced as separate lines
  • Any utility rebate the equipment qualifies for at your address
  • Manufacturer warranty terms and our labor coverage
  • The total price for that option

Take the time you need. Nothing goes on the calendar until you choose.

Scheduling the installation and filing the permit

Once you pick an option, we set the install date with you and file the mechanical permit with the office that covers your parcel.

  • HOA or condo approvalIf the association has to approve the outdoor unit, we send it the specs and our certificate of insurance. We set the date only after it approves.
  • RentalsWe plan the date around your booking calendar.
  • Utility pre-checksIf your rebate needs one (Duke's Home Energy Check or KUA's energy audit), we get it booked before install day so the rebate isn't lost.

Installation day

The crew lays floor protection along the path to the indoor unit and recovers the refrigerant from the old system. Then the old equipment comes out.

  • Indoors The new air handler or coil goes in. In an attic install, that means a secondary drain pan or a float shut-off, because a clogged condensate line above a ceiling is how water stains start. The drain line is trapped and sloped.
  • Outdoors The condenser sits on a level pad and is anchored against wind loads, as the Florida Building Code requires. Refrigerant lines are flushed and reused or replaced, depending on their condition and the new equipment. The lines are pressure-tested and pulled into a deep vacuum, then the system is charged to the manufacturer's spec.
  • Electrical The unit is connected at the disconnect, with breaker and wire size checked against the new nameplate. Since 2024, Florida law has let a licensed AC contractor replace the disconnect, breaker and wiring on the AC's own circuit. A new circuit or panel work still needs a licensed electrician. We'll tell you at the assessment if your home needs one.

Commissioning, inspection and walkthrough

Before we leave, we measure airflow, static pressure, temperature split and refrigerant charge, and we run water through the condensate drain to confirm it clears. The thermostat is set to control humidity, not just temperature.

We schedule the final inspection with the permit office and meet the inspector when needed. At the walkthrough we show you the filter, the thermostat settings and the drain cleanout. You also get the paperwork: model and serial numbers, the AHRI certificate, the permit details and the warranty information.

How Long an AC Installation Takes

On site, most straight changeouts take one working day. The dates around that day depend on approvals and the permit office, so we give you firm dates once those are known.

  1. Assessment and proposal

    What decides the timingBooking the visit, then running the load calculation

    General rangeProposal follows the visit

  2. HOA or condo approval

    What decides the timingYour association's review process

    General rangeSet by the association

  3. Permit

    What decides the timingYour permit office. Osceola County lists AC change-outs as quick permits; Orange County reviews a change-out permit before issuing it.

    General rangeSet by the office

  4. Tap a job type to compare the on-site days.

  5. Final inspection

    What decides the timingBooked with the permit office after the install

    General rangeSet by the office

A typical Kissimmee replacement

Illustrative example, not a specific customer.

  • The house: a 1980s single-story block home in Buenaventura Lakes. It runs an R-22 system with the air handler in the garage and ducts in the attic.
  • The assessment: tape failing at several attic duct joints, and a condenser pad that has settled.
  • The load calculation: it comes in below the old unit's size, because the attic insulation was topped up a few years back.
  • The proposal: a smaller two-stage AC, resealed ducts and a new pad.
  • The schedule: the duct work runs alongside the equipment swap, so the install is planned as a two-day job. Osceola County's change-out inspection follows.

Storm season

Hurricane season runs June 1 to November 30, and Kissimmee has been hit directly before: Hurricane Charley's eye crossed the city in August 2004. After a named storm, contractors, supply houses and permit offices across Central Florida all get busier, which can stretch every stage above. The outdoor unit is anchored for wind on every install, whatever the season.

Air Conditioner Types We Install, and Which Kissimmee Homes They Suit

We install straight air conditioners: cooling equipment paired with a separate heat source. Which setup fits depends on what heats your house now and how much of the system you're replacing.

What describes your home?

  • Split AC with a new air handler

    How it's set up Outdoor condenser plus an indoor air handler and coil; any heat comes from electric heat strips
    Where it fits in Kissimmee Ducted homes with the air handler in a closet, garage or attic. Read the energy-code note before choosing this for a full changeout.
  • Split AC with a coil on a gas furnace

    How it's set up Condenser plus a matched coil on an existing gas furnace
    Where it fits in Kissimmee The smaller number of Kissimmee homes heated by gas
  • Packaged AC unit

    How it's set up Compressor, coil and blower in one outdoor cabinet, ducted through a wall or under the floor
    Where it fits in Kissimmee Many manufactured homes, and houses built without an indoor equipment closet
  • Two-stage or variable-speed split AC

    How it's set up Same layout as a split system, with a compressor that runs at lower capacity most of the day
    Where it fits in Kissimmee Homes with long daily run times, west-facing glass, or humidity that never comes down

Energy code note

Florida's current energy code doesn't allow electric resistance heat to be the primary heat source when the complete central system is replaced in our climate zone. A straight AC still fits a home heated by gas, or a job that replaces only part of the system. For most whole-system changeouts in Kissimmee, the code points to a heat pump, so we also offer heat pump options for a full-system replacement. We confirm how the rule applies to your home at the assessment.

For a garage conversion, Florida room or addition the ducts can't reach, we also offer ductless mini-split options.

Air Conditioner Brands We Install in Kissimmee

We install central air conditioners from Carrier, Lennox, Rheem, Trane, Goodman, Daikin, Bryant and York, along with other manufacturers. If you already prefer a brand, tell us at the assessment. Otherwise we'll recommend the model that fits the load, the budget and any rebate you're aiming for.

  • Carrier
  • Lennox
  • Rheem
  • Trane
  • Goodman
  • Daikin
  • Bryant
  • York

Brand names are used for reference only and do not imply endorsement or affiliation. Model availability varies.

Good, Better, Best: Which System Tier Fits Your Home?

Most brands sell air conditioners in three tiers, and the difference is the compressor. In Kissimmee's humidity, that difference shows up in how dry the house feels as much as in the power bill.

Good: standard efficiency

Single-stage, about 14.3–15.2 SEER2
How it runs Fully on or fully off. Simple, proven and the lowest upfront cost.
Humidity control Good when sized correctly. Shorter cycles remove less moisture than staged systems.
Best fit Budget-focused replacements, long-term rental homes, or a home you may sell in a few years

Better: two-stage

About 15.2–17 SEER2
How it runs Runs on a lower stage most of the day and switches to full capacity on the hottest afternoons.
Humidity control Better. Longer, steadier cycles pull more moisture out of the air and run more quietly.
Best fit Families who want lower bills and a drier house. Many models reach 15.2 SEER2, where Duke Energy's AC rebate starts.

Best: variable-speed

About 17–20+ SEER2
How it runs The compressor and blower ramp up and down in small steps instead of cycling on and off.
Humidity control Best. Long, low-speed run times give the most even temperatures and the strongest moisture removal.
Best fit Long run times, west-facing glass, humidity complaints, or owners staying 10+ years

Kissimmee Homes and What Each Type Needs

Kissimmee's housing mixes eras and ownership types. Census figures for the city (ACS 2020–2024) show:

  • The median home was built around 1992.
  • About 43% of homes are in multi-unit buildings.
  • More than half of households rent.

Each type changes something about the install.

Older homes near downtown and Lake Tohopekaliga

What we look at Closet size, ducts added after the house was built, panel age
How it changes the job Duct sizing and panel capacity often limit the equipment as much as the load does

1970s–90s subdivisions such as Buenaventura Lakes

What we look at Original attic ductwork, air handlers in the garage or attic, R-22 equipment
How it changes the job Duct sealing or replacement is often part of the job

Master-planned communities such as Celebration

What we look at Architectural review rules for exterior equipment
How it changes the job We supply specs for review; the community may set placement and screening

Vacation homes around ChampionsGate and Four Corners

What we look at Number of systems, sleeping capacity, booking calendar
How it changes the job Load sized for a full house; install planned between stays

Condos and townhomes

What we look at Closet air handlers, condensers on shared pads or roofs
How it changes the job Association approval and a certificate of insurance before work starts

Manufactured homes, including communities around Campbell and Osceola Park

What we look at Data plate, package unit or downflow air handler with ducts under the floor
How it changes the job Equipment must be approved for manufactured housing and matched to the data plate

Long-term rentals

What we look at Tenant access, the owner's budget and hold period
How it changes the job Standard-efficiency equipment is common; we coordinate access with the tenant or manager

Seasonal homes

What we look at How the house is kept while empty
How it changes the job Humidity limits and drain alerts matter more than top-tier efficiency

Rental and second homes: what changes in the install

Experience Kissimmee, the county's tourism office, counts more than 30,000 vacation homes in the area. A house that sleeps 12 carries more heat and moisture than the same floor plan with a family of four, so our load calculation uses sleeping capacity, not the bedroom count.

Shutting the AC off between stays invites mold in this climate. For homes that sit empty, we pair the new system with a Wi-Fi thermostat setup that holds a temperature and humidity limit the owner can check remotely. A Wi-Fi float switch can also alert the owner before a clogged drain reaches a ceiling. Share your booking calendar when you call (844) 520-1341, and we'll plan the install date around check-outs and check-ins.

Condo, townhome and HOA approvals

Celebration has an Architectural Review Committee, and many associations in the area review changes to exterior equipment, including where the condenser sits and how it's screened. We provide equipment specs and a certificate of insurance and set the install date after approval. Condo owners should also check whether the condenser sits on a common-area pad or roof that the association controls.

Sizing for Florida Humidity, Not Just Heat

In Kissimmee, the moisture is the harder half of the job. The nearest long-term weather station is at Orlando International Airport. There, summer mornings average roughly 88–91% relative humidity, and about 110 days a year reach 90°F or hotter. An air conditioner that cools without drying leaves the house cold, damp and musty.

Orlando International Airport weather station

Summer morning relative humidity88–91%
Days a year at 90°F or hotterAbout 110

Why oversized systems feel clammy

An air conditioner removes moisture only while its coil runs cold enough to condense water. It also has to run long enough for that water to drip into the pan and drain away. A system that's too big reaches the thermostat setting in a few minutes and shuts off. The temperature drops, but the humidity stays, and water left on the coil can evaporate back into the house. Short cycling also wears out compressors and contactors faster.

Compressor run time

On Off Time
Moisture removed
On Off Time
Moisture removed

Why rules of thumb fail

"One ton per 500 square feet" ignores what drives the load in a Kissimmee home:

  • West-facing windows and sliding doors
  • Attic insulation levels and duct location
  • Ceiling height and open floor plans
  • How many people live in the home, or how many guests a vacation rental sleeps
  • Whether the air handler and ducts sit in a hot attic

How we size

Every quote starts with an ACCA Manual J load calculation. We then select equipment with Manual S, checking both total capacity and the sensible heat ratio, which shows how much of the system's work goes to cooling and how much to drying. Florida's energy code requires this kind of sizing for new homes. On a replacement we do it anyway, because the old unit's tonnage may have been a guess. If a home stays damp even with a well-sized system, we'll talk through variable-speed equipment or adding a dehumidifier to the system.

Refrigerant and Efficiency Rules for a New AC in Florida

Two federal rules shape what you can buy: the refrigerant transition and the regional efficiency minimums.

R-22

Production and import ended January 1, 2020. Older Kissimmee systems still run on it, but what's left is reclaimed and expensive. A leaking R-22 system is almost always a replacement conversation.

R-410A

New split systems have moved to refrigerants with lower climate impact. Under an EPA rule finalized in May 2026, a split system whose components were made or imported before January 1, 2025 can still be installed. That means leftover R-410A stock stays legal until it runs out. Each option in your proposal names its refrigerant.

R-454B and R-32

Most new equipment uses one of these. Both are rated A2L, meaning mildly flammable, and Florida's mechanical code requires them to be installed to the ASHRAE 15 safety standard. An A2L outdoor unit can't be paired with an old R-410A coil; the whole system has to match.

Federal efficiency minimums

Equipment Federal minimum in Florida (Southeast region)
Split AC under 45,000 Btu/h (about 3.75 tons)
14.3 SEER2
Split AC 45,000 Btu/h and up
13.8 SEER2
Packaged AC unit
13.4 SEER2

Florida has no separate EER2 requirement; that one applies only in the Southwest. Source: 10 CFR 430.32.

What Air Conditioner Installation in Kissimmee, FL Costs

As a general estimate, replacing a split central air conditioner and its matching indoor unit in a typical Kissimmee single-family home tends to land somewhere around $5,000 to $12,000. Variable-speed equipment, larger homes, and jobs that add duct or electrical work can run above that.

These figures are general estimates for planning, not actual prices. What you pay depends on your home, the equipment you choose and what the assessment finds.

What moves the price up or down

Capacity

A correctly sized system is sometimes smaller, and cheaper, than the one it replaces.

Efficiency and compressor type

Single-stage, two-stage and variable-speed units differ in price and in how well they dry the air.

Where the indoor unit sits

Attic installs take more labor than a hall closet or garage, and they need overflow protection.

Ductwork

Leaky or crushed attic ducts can undo a new system. Sealing or replacing them is a separate line.

Electrical

Older panels sometimes need a new breaker, disconnect or wire size for the new unit.

Refrigerant lines

Depending on their condition and the new equipment, we flush and reuse them or run new ones.

Site and access

Two-story homes, tight closets, condo or HOA requirements, a raised pad in a flood-prone spot, or a surge protector all affect the total.

For actual prices, connect with our professionals.

Request a Written Proposal (844) 520-1341

Rebates, Incentives and Financing for a New AC

For a straight air conditioner, utility rebates in Kissimmee are modest, and the federal tax credit has ended. The amounts below come from each utility's own pages, checked in October 2026, and can change without notice.

Kissimmee Utility Authority (KUA)

Rebate on a straight AC

None

KUA's equipment rebate is for heat pumps.

Before you install

KUA's rebate page says an in-home energy audit must be done before approval.

Duke Energy Florida

Rebate on a straight AC

$300

for an AC rated 15.2 SEER2 or higher

Before you install

A Home Energy Check before work starts, or one done in the past 24 months

OUC

Rebate on a straight AC

None listed

OUC's rebate is for heat pump systems.

Before you install

Nothing for a straight AC

KUA's other rebates can still apply to an AC project:

  • Duct leak repair50% of the cost, up to $200
  • A smart thermostat50%, up to $100
  • Insulation upgradesUp to $300, R-30 minimum
  • Larger rebates

    Heat pumps qualify for larger rebates from all three utilities.

  • Doesn't apply here

    FPL doesn't serve Kissimmee, so FPL rebates you've read about won't apply here. Your utility is printed on your electric bill.

  • Ended

    Federal tax credit: the 25C credit doesn't apply to equipment installed after December 31, 2025.

  • Not open yet

    Florida's income-based home energy rebates (the Florida Energy Saver Program) had not opened as of October 2026.

  • Provided

    Rebate paperwork: we provide the AHRI matched-system certificate that utilities ask for.

  • Available

    Financing: financing options are available. Ask about current terms during the assessment.

Permits and Inspections: City of Kissimmee vs. Osceola County

Every AC change-out here needs a mechanical permit and a final inspection. Florida's 2026 permit-exemption law (HB 803, effective July 1, 2026) lets some small single-family projects skip a permit, but not mechanical work. The City of Kissimmee's HB 803 page says so directly. Which office issues the permit depends on your parcel, not your mailing city. Plenty of homes with a "Kissimmee" address sit outside city limits.

  • Mechanical permit Required
  • Final inspection Required
  • HB 803 permit exemption Not for mechanical work
Permit office

City of Kissimmee Permitting Division, 101 Church St

How the change-out is handled

Mechanical permit through the city's EnerGov portal, then a final inspection. The city's "Check City Limits" map confirms whether an address is inside.

Permit office

Osceola County Building Office, 1 Courthouse Square, Suite 1400

How the change-out is handled

The county lists AC change-outs as quick permits and runs an "AC Change Out Final" inspection, with a virtual inspection option.

How the change-out is handled

Mechanical permit through Orange County's Fast Track system, reviewed before it's issued

How the change-out is handled

Mechanical permit through the city

Permit office

Polk County or Lake County

How the change-out is handled

Confirm with us that we cover the address. Call (844) 520-1341.

We file the permit and schedule the inspection. In Florida, AC installation is licensed work under Chapter 489 of the Florida Statutes, and we pull the permit under our state license.

Ducts that are replaced or extended have to meet the energy code's sealing requirements. Existing ducts that stay don't have to be tested, but we inspect them anyway.

Where We Install: Permit Offices and Utilities by Area

We install throughout Kissimmee and the surrounding communities. For a new AC, your area decides two things: who issues the permit and which utility's rebate rules apply.

  • Kissimmee (Downtown / US-192 Corridor)

    Permit officeCity of Kissimmee inside city limits; Osceola County outside
    Electric utilityMostly KUA
  • Buenaventura Lakes

    Permit officeOsceola County
    Electric utilityCheck your bill
  • Campbell

    Permit officeOsceola County
    Electric utilityCheck your bill
  • Celebration

    Permit officeOsceola County
    Electric utilityDuke Energy Florida
  • Hunters Creek

    Permit officeOrange County
    Electric utilityDuke Energy Florida
  • Poinciana

    Permit officeOsceola or Polk County, by village
    Electric utilityDuke Energy Florida
  • St. Cloud

    Permit officeCity of St. Cloud
    Electric utilityOUC
  • ChampionsGate

    Permit officeOsceola County
    Electric utilityCheck your bill
  • Four Corners

    Permit officeOsceola, Polk, Lake or Orange County, by parcel
    Electric utilityCheck your bill

We also install in Davenport, Clermont, Winter Park, Altamonte Springs, Sanford, Apopka, Ocoee and Lake Mary, where the permit comes from that city or county.

Full list of communities we cover

AC Installation FAQs for Kissimmee, FL Homeowners

Straight answers on cost, permits, equipment, warranty and rebates for a new central AC.

What's a realistic budget for replacing a central AC in Kissimmee?
It depends mostly on capacity, the efficiency tier, where the indoor unit sits, and whether the ducts or electrical need work. Your actual price comes in writing after we assess the home.
Can a new AC be installed in one day?
A like-for-like changeout usually is, on site. Duct changes, moving the air handler or adding an electrical circuit can stretch the work to two or three days. The final inspection comes afterward, on the permit office's schedule.
My address says Kissimmee. Why would my AC permit come from Osceola County?
A Kissimmee mailing address covers a lot of unincorporated county land. If your parcel is outside city limits, the permit comes from Osceola County, or from Orange County in Hunters Creek. The City of Kissimmee's city-limits map and your property tax bill both show your jurisdiction, and we check it before we quote.
Does Florida's new permit law mean I can skip the AC permit?
No. HB 803, in effect since July 1, 2026, lets some small single-family projects skip a permit, but mechanical work such as an AC change-out isn't included. The City of Kissimmee confirms this.
Which SEER2 rating makes sense for a Kissimmee home?
The legal floor is 14.3 SEER2 for most home split systems here. If Duke Energy is your utility, 15.2 SEER2 or higher matters, because that's where its AC rebate starts. Beyond that, the right rating depends on how many hours your system runs and how long you plan to stay, and the proposal shows each option side by side.
Can I still have an R-410A air conditioner installed?
Yes, if the equipment was made or imported before 2025. An EPA rule finalized in May 2026 removed the installation deadline for that stock, so it can go in until supplies run out. Most new equipment uses R-454B or R-32, and your proposal says which refrigerant each option uses.
Can you replace just the outdoor unit and keep my indoor coil?
We usually advise against it. The outdoor unit and indoor coil are rated as a matched pair, and the newer A2L refrigerants can't run through an older R-410A coil. A mismatched system can lose efficiency and run into warranty problems.
Do I have to register my new AC to keep the manufacturer warranty in Florida?
No. Under Florida law, a manufacturer can't make the warranty depend on registration when a licensed contractor installs the system. We register it anyway and give you the confirmation, because it speeds up any later claim.
Which utility rebate can I get on a new air conditioner in Kissimmee?
That depends on who sends your electric bill. Duke Energy Florida rebates straight air conditioners that meet its efficiency level, after a Home Energy Check. KUA and OUC currently list equipment rebates for heat pumps only, though KUA's duct, thermostat and insulation rebates can still apply. Programs change, so we confirm yours at the assessment.
Can I replace the AC in my Kissimmee rental home without flying in?
Yes. Someone needs to give the crew access on assessment day and install day, and that can be your manager or your tenant. You can review the proposal, approvals and paperwork remotely.
Does my HOA have to approve a new outdoor AC unit?
Often, yes, especially if the condenser moves, changes size or needs new screening. Celebration, for example, has an Architectural Review Committee for exterior changes. We send the association the equipment specs and our certificate of insurance, and we set the install date after it approves.

Not sure how this applies to your home? Call us and we'll talk it through.

(844) 520-1341

Get a Written AC Installation Quote in Kissimmee

Tell us what your current system is doing, or not doing. We'll measure the home, run the load calculation and put two or three options in writing, with an honest word if a repair makes more sense.

Call (844) 520-1341
Business Kissimmee HVAC
Address 1551 N Kelley Ave, Kissimmee, FL 34744
Call: (844) 520-1341